Pull the lever in or push down on Brake lever position adjustment ment, make sure that the rear the pedal. Hold the lever or pedal steps: brake does not drag. Loosen the locknut "1". Loosen the bleed screw and allow b. Remove the pad pin and brake pads "4". Install the pad pin plug "10". Loosen the pad pin "3". Remove the rear wheel "4" and Pad pin plug: e. Connect the transparent hose "5" brake caliper "5".
PADS" section. Check: eral times to find the tightest point. Tighten the locknuts. Always adjust each front fork to 2. Remove the air bleed screw "1" the same setting. Uneven adjust- and release the internal pressure ment can cause poor handling and from the front fork. Adjust: ing bearings. Install the washer "5", upper bracket "6", washer "7", steering stem nut "8", handlebar "9", han- Steering ring nut adjustment dlebar upper holder "10" and steps: number plate "11".
Remove the number plate. Lubricate the following areas Loosen the screws stator "1". Those who have little knowledge and skill concerning servicing are request- ed not to undertake inspection, adjustment, disassembly, or reassembly only by reference to this manual.
Yamaha bond No. Blow out all passages and position sensor "1" except when jets with compressed air. Measure: chamfered side "a" to the right. Install: Insert the set pin "3" included in own- er's tool kit to remove the bolt push rod.
Check: 6. Bolt brake pedal Shift the brake pedal downward. Lock washer Refer to removal section. Straighten the lock washer tab and Clutch spring free use the clutch holding tool "4" Place an aluminum plate "a" between the teeth of the primary drive gear "2" and driven gear "3". Governor assembly Dowel pin Refer to removal section. Install: 1. Remove: 1. Install: Ignition timing B.
Bolt brake pedal : 26 Nm 2. SHAFT" section. Main axle Refer to removal section. Remove: the sliding gear, then install. Nut rear wheel axle Rear wheel axle Drive chain puller Rear wheel Refer to removal section. Apply the lithium soap base grease on the oil seal lip. Drain the brake fluid. Refer to removal section. Brake hose holder protector Union bolt Brake hose Brake caliper piston dust seal Refer to removal section.
Brake caliper piston seal Refer to removal section. Washer Push rod Rear Brake master cylinder kit Install: 2. Pass the brake hose through the cable guide "1". The front fork requires careful atten- tion. So it is recommended that the 3. Tighten: base valve with specified torque. Temporarily tighten the damper as- sembly. Tighten: 5. Tube guide Apply the lithium soap base grease on the throttle cable end and tube guide cable winding portion. Tighten: Support the machine securely so there is no danger of it falling over.
Install: 4. Adjust: 3. It may lead to Disconnect the spark plug cap Replace. Connect the dynamic spark tester place. Check each couplers and wire connection. Disconnect the solenoid valve coupler. Connect 12V battery to the sole- noid valve coupler. Check entire ignition system for connection. Insert the thin electric conductors Stop the engine. There- "1". Click here to download your YZ Y owners manual. Click here to download your YZ Z owners manual.
Click here to download your YZ S owners manual. Click here to download your YZRY owners manual. Click here to download your YZ A owners manual. Click here to download your YZ AA1 owners manual.
Click here to download your YZ B owners manual. Click here to download your YZ FB owners manual. This is an awesome site, very helpful. Would it be possible for you to let me know the password needed to edit the files so that I can remove the non-English pages? Thanks for all the available books I wanted to know if it was available manual Yamaha YZ Thank you. My yz 2 stroke does only take ml then the oli comes out the oli level bolt Is this normal or not.
Your email address will not be published. Skip to content About. Thanks, Jim. Pingback: Does it get rusted whenever you take it to the car wash?
Im looking for manual for YZ Can you upload it here? I have a yamaha yz
0コメント